NEW! - Big savings on fly rod, reel and fly line combo's - VIEW THE COLLECTION

NEW! - Big savings on fly rod, reel and fly line combo's - VIEW THE COLLECTION

SPINING A FLY ROD - TO SPINE OR NOT TO SPINE

  • Fly rod blanks tend to naturally want to bed more in one direction than the other. This is caused by an effect called the “Spine” and often there is more than one on a blank. The spine is a result of the manufacturing process and is the location of the join or overlap of a graphite or glass flag as it is rolled around the mandrel.
  • Basically it is a slightly thicker section in the tube wall. This thick section is slightly stiffer than the rest of the tube and presents a greater resistance to bending. (Blanks that use helical wound construction tend not to exhibit a pronounced spine)
  • You can find the spine in your blank by holding the blank at a 45 degree angle with one hand near the tip and then by pressing down and rotating at the same time with fingers of your other hand. The resistances you feel on both sides are the high points or spines. 
  • You’ll likely feel the blank Jump or pop over and want to sit a certain way. You may feel a couple of potential spines, but somewhere in there you’ll feel the most pronounced pop ,or reaction to your bending. When you get tot this spot - you’ve spined your blank.
  • The inside of the curve (where the blank has come to rest under your fingers) is the softer side of the blank. The outside of the curve is actually where the spine is - the stiffer side.

Spining a fly rod

 

NOW THAT YOU FOUND THE SPINE YOU HAVE AT LEAST 4 CHOICES WHAT TO DO WITH IT.

  1. Place the guides on the inside of the curve - the weaker side. By placing the guides on the inside of the curve you will get (marginally) better lifting power, as you will be pulling against the spine or natural curve of the blank.
  2. Place the guide on the outside of the curve - the (marginally) stiffer side. Placing your guides on the outside curve will result in the rod being (moderately) stiffer on the forward cast.
  3. Ignore the spine altogether and align the rod sections so give the straightest most aesthetically pleasing result. (our preference) This is what most of the large commercial rod manufactures do.
  4. Place the guides out at 90 degrees to the spine. I’e off to the side at right angles to the spine. Don Green, the great rod designer for Fenwick and Sage advocated this method. His reasoning was that the rod should track straight on both backcast as well as forward cast in order to be most accurate. 
    Putting the spine on the top or bottom of the rod means that the rod will tend to kick slightly out of line on either the back or forward cast. By pacing the spine out at 90 degrees the spine is apply the same effect whether on the back or forward cast. (We like this aproach too)

 

THE TRUTH?

The subject of spining rods has & continues to cause huge debate. The truth is that under the tension of the cast the rod will always bend according to the tension of the fly line against the guides and tiptop, the effect of the spine on a fully loaded rod is negligible. - So truly, it matters little (all respect to the great Don Green) 

Do what you feel is best for your build, it's you rod - follow your bliss.

 

3 Antworten

Yoshitake Boba
Yoshitake Boba

Dezember 24, 2018

Which option should I choose when building a spey rod, particularly for skagit casting? It is multi dimensional cast so I do not know which axis of the blank would be effective.

Jeff Krushinski
Jeff Krushinski

Januar 31, 2017

I know this is an older post, but question for the author.. I like the idea of the guides 90 degrees off the spine. I’m getting ready to build a 4 piece fly rod and am considering alternating the spine from one side to the other, so that the finished rod, held in the hand in a normal position (guides on the bottom) and starting from the butt section, the spine would be right side, left side, right side, and left side. Do you think this configuration would have any negative or positive affects.

Mark
Mark

Dezember 07, 2016

I think you’ve got a couple of things backwards; placing the guides on the spine’s side will not produce a stiffer forward cast. “Place the guides on the inside of the curve – the weaker side. By placing the guides on the inside of the curve you will get (marginally) better lifting power, as you will be pulling against the spine or natural curve of the blank.” Wouldn’t you be pulling against the softer side, it’s natural curve which is weaker than putting pressure against not down upon the spine?

Schreiben Sie einen Kommentar

Kommentare werden vor der Veröffentlichung genehmigt.


Vollständigen Artikel anzeigen

Fly fishing Knots how to tie the slim beauty knot step 3
How To Tie The Slim Beauty Knot

Juni 29, 2022 2 min lesen.

The slim beauty is one of the most popular fly fishing knots in use today. It is a great knot for connecting class tippets to shock tippets as well as tippet sections to butt sections. This knot is strong, easy to tie on the water, and has a very low profile.
Vollständigen Artikel anzeigen
Fly Fishing the Limay Rover with an Epic 8 weight fiberglass fly rod
Fly Fishing the Limay River

Juni 13, 2022 2 min lesen.

It is the end of the fishing season in Patagonia Argentina. Two of my buddies, Marcos Hlace, Diego Soto and myself decided to fish for the mighty migratory trout at the upper Limay River, a must to at least once in a life time.
Vollständigen Artikel anzeigen
fly casting improve your distance
Fly Casting - Sharpen Your Shooting

Juni 13, 2022 5 min lesen.

Double your line length in a single cast without false casting Any fly fisher knows that stripping in and lengthening – or “shooting” line – is part of the fly-fishing process. Understanding how and when to lengthen line will sharpen your shooting and make a significant difference in ease and performance
Vollständigen Artikel anzeigen