NEW! - Big savings on fly rod, reel and fly line combo's - VIEW THE COLLECTION

NEW! - Big savings on fly rod, reel and fly line combo's - VIEW THE COLLECTION

Spining a fly rod. How to find the spine on a fly rod

December 18, 2018 3 min read

Spine on a fly rod how to find the spine

 Spining a Fly Rod - To Spine or not to Spine

  • Fly rod blanks tend to naturally want to bed more in one direction than the other. This is caused by an effect called the “Spine” and often there is more than one on a blank. The spine is a result of the manufacturing process and is the location of the join or overlap of a graphite or glass flag as it is rolled around the mandrel.
  • Basically it is a slightly thicker section in the tube wall. This thick section is slightly stiffer than the rest of the tube and presents a greater resistance to bending. (Blanks that use helical wound construction tend not to exhibit a pronounced spine)
  • You can find the spine in your blank by holding the blank at a 45 degree angle with one hand near the tip and then by pressing down and rotating at the same time with your other hand. The resistance you feel are the high points or spine. 
  • You’ll likely feel the blank Jump or pop over and want to sit a certain way. You may feel a couple of potential spines, but somewhere in there you’ll feel the most pronounced pop ,or reaction to your bending. When you get to this spot - you’ve spined your blank.
  • The inside of the curve (where the blank has come to rest under your fingers) is the softer side of the blank. The outside of the curve is actually where the spine is - the stiffer side.

Spining a fly rod finding he spine on a fly rod

 

Now that you found the spine you have at least 4 choices what to do with it.

  1. Place the guides on the inside of the curve - the weaker side. The natural curve. The thinking here is that placing your guides on the inside curve may result in the rod being (moderately) stiffer on the forward cast and the rod will sit more naturally when fighting fish. (it's actually going to bend in any direction it's pulled)
  2. Place the guides on the outside of the curve - the (marginally) stiffer side. By placing the guides on the outside of the curve you may get (marginally) better lifting power, as you will be pulling against the spine or natural curve of the blank.
  3. Place the guides out at 90 degrees to the spine. I’e off to the side at right angles to the spine. Don Green, the great rod designer for Fenwick and Sage advocated this method. His reasoning was that the rod should track straight on both backcast as well as forward cast in order to be most accurate.
    Putting the spine on the top or bottom of the rod means that the rod will tend to kick slightly out of line on either the back or forward cast. By placing the spine out at 90 degrees the spine will apply the same effect whether on the back or forward cast.
  4. Ignore the spine altogether and align the rod sections to give the straightest most aesthetically pleasing result. (our preference) This is what most commercial rod manufacturers do.


The Truth?

The subject of spining rods has caused & continues to cause huge debate. The truth is that under the tension of the cast the rod will always bend according to the tension of the fly line against the guides and tiptop, the effect of the spine on a fully loaded rod is negligible. - So truly, it matters little (all respect to the great Don Green) 

Do what you feel is best for your build, it's your fly rod - follow your bliss.


Leave a comment

Comments will be approved before showing up.


Also in The Drift - Fly Fishing, Fly Casting and Fly Rod Building

Bearhawk fly fishing fly rods
BEARHAWK LIMITED EDITION FLY RODS

July 04, 2022 2 min read

BEARHAWK LIMITED EDITION FLY RODS The Bearhawk Limited Edition* line of fly rod building kits and fly rods are inspired by fishing trips in my friends Bearhawk airplane. We always get there fast and can land in a places where most planes simply can not go.
Read More
Fly fishing Knots how to tie the slim beauty knot step 3
How To Tie The Slim Beauty Knot

June 29, 2022 2 min read

The slim beauty is one of the most popular fly fishing knots in use today. It is a great knot for connecting class tippets to shock tippets as well as tippet sections to butt sections. This knot is strong, easy to tie on the water, and has a very low profile.
Read More
Fly Fishing the Limay Rover with an Epic 8 weight fiberglass fly rod
Fly Fishing the Limay River

June 13, 2022 2 min read

It is the end of the fishing season in Patagonia Argentina. Two of my buddies, Marcos Hlace, Diego Soto and myself decided to fish for the mighty migratory trout at the upper Limay River, a must to at least once in a life time.
Read More